EN
ar
bg
hr
cs
da
nl
fi
fr
de
el
hi
it
ko
no
pl
pt
ro
ru
es
sv
tl
iw
id
lv
lt
sr
sk
sl
uk
vi
et
hu
th
tr
fa
ms
hy
ka
ur
bn
mn
ta
kk
uz
ku
Vibrating Wire Strain Gauges for Bridge, Tunnel & Dam Monitoring: Complete Selection Guide
The global construction industry is experiencing a massive surge in large-scale infrastr...
Accurate Magnetostrictive Displacement Meter - Kingmach
Magnetostrictive Displacement Meter
Underground works, dams, and slopes depend on precise displacement data to stay safe. Magnetostrictive displacement meters have earned their place in these applications through a sensing principle that sidesteps many of the wear issues common with contact-based instruments. At Kingmach, we build these meters with the real-world field conditions in mind—water ingress, temperature swings, and limited access. The result is a line of instruments that deliver stable readings over years without demanding constant attention. Whether embedded in a borehole or surface-mounted on a structure, our meters connect seamlessly to most data loggers and automation systems. This text walks through what the technology does, how our implementation differs from generic alternatives, and which scenarios benefit from it most.
Technical Detail
Configured around process stability, mold life, and long-term uptime.
A magnetostrictive displacement meter works by sending a current pulse along a waveguide. When the pulse meets the magnetic field of a position magnet, a torsional strain pulse reflects back—timing gives the distance. This means the measurement happens without physical contact between the sensing element and the magnet, so there’s nothing to wear down. Kingmach units use this foundation and add practical touches for field use: sturdy stainless housing, IP67 or higher sealing as standard, and electronics that cope with voltage dips on site. Output is typically 4-20 mA, Modbus, or SDI-12—formats that slot into nearly any monitoring network. We stock several stroke lengths, and if your project calls for a non-standard range or a specific mounting bracket, our engineering team can adjust the design. The instruments have seen service in dam crest monitoring, landslide early-warning systems, and structural health checks on bridges. In each case, the feedback we get is consistent: once installed and calibrated, they rarely need re-zeroing, even after seasonal ground movement. Because we position ourselves in the mid-tier, you get field-tested reliability without paying for laboratory-grade frills that real-world sites seldom require.
News
Industry updates
Hollow Load Cells for Bridge Cable & Anchor Monitoring: Selection Guide & Specifications
Cable-stayed bridges, pre-stressed concrete decks, and dam anchors rely on precisely cal...
Understanding the 9 Types of Load Cells: An Engineering Selection Guide
The Type of Load Cell Is Not a Product Choice—It Is an Engineering Decision In ...
Products
Production modules
Magnetostrictive Displacement Meter JMCW-21XXADT
Magnetostrictive Displacement Meter JMCW-21XXADT
View Details
FAQ
Common technical questions
What sets a magnetostrictive displacement meter apart from a potentiometric or LVDT sensor?
The main difference is the non-contact sensing. Potentiometric types rely on a wiper touching a resistive track, which eventually wears. LVDTs also have moving cores. Magnetostrictive meters have no sliding electrical contacts on the measuring path, so they tolerate vibration, dirt, and moisture better in long-term outdoor installations.
Can the meter work if the magnet is misaligned or the rod is bent slightly?
A small lateral offset of the magnet is usually fine as long as it stays within the specified guidance zone. A bent rod, however, can block the waveguide signal. In practice, installers aim to keep the rod straight and the magnet free from side load. The mounting brackets we supply help maintain alignment.
How do you calibrate these sensors, and how often is it needed?
Calibration is done at the factory against a laser reference before shipment. On site, you verify the output at a known zero position. Many users find they don’t need to recalibrate unless the sensor is physically disturbed. We can provide a calibration certificate and recommend a simple field check procedure.
Are the electronics separate from the sensing rod? What’s the max cable length?
In most Kingmach models, the electronics are housed in a terminal box at the rod end, making replacement possible without pulling out the whole sensor. Cable length between sensor and readout can reach several hundred meters with proper shielding; we confirm acceptable lengths based on the output signal type during ordering.
Can I use one meter to measure both static and dynamic displacement?
Yes, the measuring principle captures position continuously. If your data acquisition system samples fast enough, you can track slow creep as well as dynamic motion like vibration. Just let us know your expected frequency range so we match the internal filter settings to avoid aliasing.
Need a solution for your project?
Share your product type, target capacity, and application requirements. Our team can review the details and recommend a practical next step.